Locate the oil drain plug and place a pan under it tocatch the oil. With a box wrench, remove the oil plug.
Note for newbies: To remove the drain plug, turn itcounter-clockwise.
- If you have a GM dual-overhead-cam EcoTec engine you mayhave a difficult time locating the drain plug on all thataluminum.
When the oil stops draining, reinstall the drain plug.
Note for newbies: To replace the drain plug turn itclockwise. Start the plug with your fingers. If it seemseven slightly hard to turn, back it out! You are crossingthe threads.
Step 2. Replace the oil filter.
Move your oil catch pan under the oil filter. Using an oilfilter wrench to get it started, remove the oil filter.(newbies: counter-clockwise, and you will get some oil onyour hand.)
- A strap type oil filter wrench is the best kind to use.A socket type oil filter tool is used with a ratchet justlike a regular socket. The problem with the socket type isthat it tends to get stuck on the filter. Use the sockettype tool if you don’t have enough clearance around theoil filter to use the strap type.
With your finger put a thin coat of oil on the new filter’sgasket to make it seal better.
Now pay attention - here’s were you can screw up royal!
With your hand, install the new oil filter. If it seemseven slightly hard to turn, back it out! You are crossingthe threads. Most filters have an instruction printed onthem to give the filter one more turn after the gasket hasmade contact.
Here’s what I recommend: screw the filter on until its"hand tight". Then use the oil filter wrench to snug it upanother 1/8 to 1/4 turn. This is critical!
When the vehicle is running, the oil pump puts the oilunder pressure. If you don’t install the oil filter tightenough, the oil will come gushing out. If that happens shutdown the engine immediately! Without oil, an engine willlock up within seconds.
The first time I changed my oil, I used the filter wrenchto tighten the filter as tight as I could get it. Wrong!The next time I went to change my oil, I couldn’t get thefilter off. Luckily I had plenty of room around the filer,so I hammered a screw driver through the body of thefilter and used the handle of the screw driver to turn thefilter off.China fan motor Suppliers--https://www.ixymotor.com/product/frp-cone-fan-motor/
Note for newbies: To remove the drain plug, turn itcounter-clockwise.
- If you have a GM dual-overhead-cam EcoTec engine you mayhave a difficult time locating the drain plug on all thataluminum.
When the oil stops draining, reinstall the drain plug.
Note for newbies: To replace the drain plug turn itclockwise. Start the plug with your fingers. If it seemseven slightly hard to turn, back it out! You are crossingthe threads.
Step 2. Replace the oil filter.
Move your oil catch pan under the oil filter. Using an oilfilter wrench to get it started, remove the oil filter.(newbies: counter-clockwise, and you will get some oil onyour hand.)
- A strap type oil filter wrench is the best kind to use.A socket type oil filter tool is used with a ratchet justlike a regular socket. The problem with the socket type isthat it tends to get stuck on the filter. Use the sockettype tool if you don’t have enough clearance around theoil filter to use the strap type.
With your finger put a thin coat of oil on the new filter’sgasket to make it seal better.
Now pay attention - here’s were you can screw up royal!
With your hand, install the new oil filter. If it seemseven slightly hard to turn, back it out! You are crossingthe threads. Most filters have an instruction printed onthem to give the filter one more turn after the gasket hasmade contact.
Here’s what I recommend: screw the filter on until its"hand tight". Then use the oil filter wrench to snug it upanother 1/8 to 1/4 turn. This is critical!
When the vehicle is running, the oil pump puts the oilunder pressure. If you don’t install the oil filter tightenough, the oil will come gushing out. If that happens shutdown the engine immediately! Without oil, an engine willlock up within seconds.
The first time I changed my oil, I used the filter wrenchto tighten the filter as tight as I could get it. Wrong!The next time I went to change my oil, I couldn’t get thefilter off. Luckily I had plenty of room around the filer,so I hammered a screw driver through the body of thefilter and used the handle of the screw driver to turn thefilter off.China fan motor Suppliers--https://www.ixymotor.com/product/frp-cone-fan-motor/
コメント